To calculate miles per hour (mph) from a measured speed over 37 feet or 50 feet, you need the time taken as well as the distance: mph = distance in feet ÷ time in seconds × 0.681818. A 50-foot measurement covers more distance, so at the same speed it takes longer; distance alone cannot tell you the mph.
The Formula for Converting Feet and Seconds to Mph
One mile is 5,280 feet, and one hour is 3,600 seconds. Converting feet per second to miles per hour therefore means multiplying by 3,600 and dividing by 5,280, which simplifies to approximately 0.681818.
Use this formula when you know how many seconds it took to cover a measured distance:
- 37 feet: mph = 37 ÷ seconds × 0.681818, or about 25.23 ÷ seconds.
- 50 feet: mph = 50 ÷ seconds × 0.681818, or about 34.09 ÷ seconds.
The result is an average speed for the measured interval. For example, covering 50 feet in 1.5 seconds gives 50 ÷ 1.5 = 33.33 feet per second; multiply that by 0.681818 to get about 22.7 mph.
Examples at 37 Feet and 50 Feet
Here are example calculations for the same elapsed times. They illustrate why the measured distance matters when converting a timed run into speed:
- 37 feet in 1 second: about 25.2 mph.
- 50 feet in 1 second: about 34.1 mph.
- 37 feet in 1.5 seconds: about 16.8 mph.
- 50 feet in 1.5 seconds: about 22.7 mph.
- 37 feet in 2 seconds: about 12.6 mph.
- 50 feet in 2 seconds: about 17.0 mph.
These comparisons assume each distance is covered in the stated time. They do not mean that 50 feet is inherently a particular mph value. If an object covers 37 feet in 1 second and then continues at exactly the same speed, it would take about 1.35 seconds to cover 50 feet, and both measurements would give roughly 25.2 mph.
How to Calculate a Speed From a Timed Distance
- Measure the course. Set the start and finish points exactly 37 feet or 50 feet apart, using the same points for every attempt.
- Time the interval. Record how many seconds pass between the object crossing the start and finish points. Use a timer or suitable speed-measuring equipment.
- Divide distance by time. This gives speed in feet per second.
- Convert to mph. Multiply feet per second by 0.681818.
For instance, if a ball travels 37 feet in 0.8 seconds, its average speed over that interval is 37 ÷ 0.8 = 46.25 feet per second. The converted speed is about 31.5 mph. A calculator can perform the arithmetic, but accurate distance and timing are just as important as the conversion.
What a Short Measurement Does—and Does Not—Show
A timed 37-foot or 50-foot interval gives average speed across that interval, not necessarily the object’s speed at every instant. If a runner accelerates, a thrown ball slows down, or a vehicle changes speed, its average over the measured section can differ from its speed at the start, finish, or midpoint.
To compare two measurements fairly, the timing points and conditions should be consistent. A speed measured over 37 feet can be compared with one measured over 50 feet if each calculation uses its own distance and elapsed time. Comparing the raw times alone is misleading: the longer distance normally takes longer at the same speed.
Short intervals also make timing errors more consequential. If the elapsed time is a fraction of a second, a small start or stop error can noticeably change the calculated mph. Hand timing may be adequate for a rough estimate, but it is not a dependable way to establish a precise speed.
Common Conversion Mistakes
- Using distance without time: 37 feet and 50 feet are lengths, not speeds. An elapsed time is essential.
- Forgetting the conversion factor: feet per second is not mph. Multiply by approximately 0.681818.
- Multiplying by time instead of dividing: speed is distance divided by time.
- Using the wrong distance: If the measured section is 37 feet, do not enter 50 in the formula.
- Assuming a longer distance means a higher speed: It only indicates more ground covered. The time determines the speed.
A useful check is that a speed of 1 mph equals about 1.467 feet per second. Thus, a result of 30 feet per second should be roughly 20.5 mph—not 30 mph.
Frequently Asked Questions
How many mph is 37 feet?
There is no single mph value for 37 feet because feet measure distance. To calculate speed, divide 37 by the time in seconds and multiply by 0.681818. For example, 37 feet in one second is about 25.2 mph.
How many mph is 50 feet?
That also depends on the elapsed time. The formula is 50 ÷ seconds × 0.681818. Covering 50 feet in one second is about 34.1 mph; covering it in two seconds is about 17.0 mph.
How do I convert feet per second to mph?
Multiply feet per second by 0.681818. For a quick estimate, multiplying by 0.682 is sufficiently close for most everyday calculations.
Can I compare a 37-foot time with a 50-foot time?
Yes, if you calculate each speed using its own distance and measured time. Do not compare the times alone, because the 50-foot interval is longer and should take more time at the same speed.
Does this calculation give instantaneous speed?
No. Dividing distance by elapsed time gives average speed over the interval. Instantaneous speed requires a measurement method that captures speed at a particular moment.
Bottom Line
For either distance, the key is the elapsed time: multiply distance in feet by 0.681818, then divide by seconds—or divide the distance by seconds and multiply the result by 0.681818. Use 37 for a 37-foot interval and 50 for a 50-foot interval. Without a time measurement, an mph value cannot be calculated.
